Panel

In the tab, you configure settings for apartment, device, calls, and SIP calls.

Apartment Settings


For correct panel functioning, you must enter information about its logical address (more information about logical address formation find here):

  • panel operation mode;

Info about operation modes

There are 2 modes available, which are intended for certain working conditions:

Wall mode is used when the panel is installed on the perimeter of the object. If this variant is chosen, on panel you must enter Building No., Unit No., Floor No., and Apartment No. to call the necessary monitor. 

Also in this mode, No unit option is available. So, to call monitor, you must enter Building No., Floor No., and Apartment No. For this option correct work, all monitors in the Apartment Settings must have to 0 value for Unit number.

Unit mode is required if the panel is installed near the unit entrance. When using this mode, it is enough to enter Floor No. and Apartment No. to call the necessary monitor.

  • building number (parameter is for Unit mode only); 
  • unit number (parameter is for Unit mode only); 
  • device number








Info

If you have more than 1 entrance panel with the same logical address, you need to specify their device numbers, starting from 1 for the main device, and from 2 to 9 for others.

Note:

To make a call between the panel and the indoor monitor visitors must enter required information that depends on the chosen operation mode.

For correct functioning, the panel and the monitor must have the same building and unit number in apartment settings. Also for monitors, you must indicate corresponding information about the floor, apartment, and device number.

If there are no such settings, you must make forwarding queues for apartments with IP addresses or SIP numbers of monitors.

Using Unit mode (according to the panel settings from the photo above), to call apartment No 1, located on the 1st floor of the 1st unit, visitors must enter 1. So, monitor with logical address (number) 0001-01-00-01 will be called. In this logical address, 0001 is a Building No., 01 stands for Unit No., 00 is a Floor No., and 01 is a number of apartment. Thus, the same logical address must be set in the monitor settings: building - 1, unit - 1, floor - 0, apartment - 1.

If Wall mode is set, to call apartment No 1, located on the 1st floor of the 1st unit, visitors must enter 1-1-1. With the No Unit option, 1-1 is enough to enter. 

 So, monitor with logical address (number) 0001-01-00-01 will be called. In this logical address, 0001 is a Building No., 01 stands for Unit No., 00 is a Floor No., and 01 is a number of apartment. Thus, the same logical address must be set in the monitor settings: building - 1, unit - 1, floor - 0, apartment - 1.

SIP settings


These settings are required for the correct work of calls via SIP protocol. Step-by-step guide how to get SIP nubmers and configure a panel for SIP calls if you use BAS-IP SIP server you can find here.

To configure SIP calls for the panel, you must enable device SIP registration and enter the following parameters: 

  • SIP server proxy that can be represented by both an IP address and a domain name.

Data format:

Before the proxy address, you must enter "sip:", e.g. sip:gb.sip.bas-ip.com. A full list of BAS-IP servers for each country is available here

If you use a third-party SIP server, you can also indicate a non-standard port in the format: 

sip:gb.sip.bas-ip.com:1506 where gb.sip.bas-ip.com is a SIP server proxy, 1506 is a non-standard port.

  • SIP server address that can be represented by both an IP address and a domain name, e.g. gb.sip.bas-ip.com.

Data format:

If you use a third-party SIP server, you can also indicate a non-standard port in the format: 

sip:gb.sip.bas-ip.com:1506 where gb.sip.bas-ip.com is a SIP server, 15061 is a non-standard port.

  • port of the STUN server;

Note:

19302 port is used for Google STUN server.

  • user SIP number (up to 20 characters); 
  • password for SIP number (up to 20 characters);

Call settings


At this part you can: 

  • enable/disable a call to the specified number when pressing the concierge button;
  • indicate the direction (number) to which the call will be made when pressing the concierge button;
  • enable/disable autocall after entering indicated in corresponding field digits count;  

Forwarding when pressing the concierge button:

You can also set up a call to a specified number when you press the concierge button using the Forwarding feature. In the Apartment number field, you must enter 1000Х, where X is the concierge monitor device number. So, for the 1st concierge monitor apartment number will be 10001. Also, you must enter the forward number in one of the formats: sip:SIP [email protected] of the SIP server or sip:any [email protected] IP address.

  • configure call max time (10-120 sec after which the panel automatically ends an outgoing call if there is no answer).
  • configure talk max time (10-300 sec after which the panel automatically ends the outgoing conversation).

Info

If the feature is disabled, the concierge is called via an internal protocol. If the system has concierge monitors, the call will go to the main monitor. If it does not answer, the call will be transferred to the other monitors in the system (if they are).

Info

Talk time for an incoming call is limited to 2 min.

Device settings


In this section you can: 

  • select preferred video quality (resolution) (640х480/1280х720/1920x1080 (optional));
  • select preferred RTP data profile;
  • adjusts a volume level of a panel speaker;
  • adjusts a screen brightness
  • enter RTSP username (login to get access to a panel RTSP stream);
  • enter RTSP password (password to get access to a panel RTSP stream);
  • enable/disable a proximity sensor. The panel will automatically turn on the keyboard backlight and face recognition feature when motion is detected at a distance of 50 cm; 
  • enable/disable connected to the panel temperature sensor. During an outgoing call, the panel will take the temperature of the person in front of the panel and display it on the called person internal monitor during the call/talk;